Advanced search

Issue Suit "KM-L" SSO(SPOSN)

Issue Suit
This Product was added to our catalogue on Friday, 08 May 2015.
102,00 $
  • Print product data sheet
  • Ask a question
  • Size chart:

  • Manufactured by: SSO (SPOSN)
Описание товара
The costume is based on the famous Soviet model of the sample of 1986. Taking all the best from the old analog, the new suit surpasses it in quality of fabric, cut, accessories and General consumer characteristics. The product is intended for professional military, law enforcement and environmental organizations, hunters, fans of active paramilitary games, etc. the Jacket of a camouflage suit with a loose fit and a classic design fastens in front with five large buttons, covered by a single vertical windproof valve. The traditional turn-down collar at the back, on the inside, has three buttons to which the removable hood of the suit is attached. The hood itself is equipped with two built-in cord ties - on the front section and in its middle horizontal part, which regulate its volume. The upper edge of the hood is cut as an improvised "visor", and in the lower front part there is a two-button flap. In the upper front part of the jacket, on the right and left, there are two patch breast pockets (160x120 mm), closed by flaps with a single button closure. The left pocket is also provided with a Central opening at the top of its flap and a corresponding internal channel for carrying a fountain pen or pencil. Below, on the right and on the left, with an offset on the sides (for the convenience of crawling), there are two additional patch pockets (180x160 mm), each of which is closed by a two-button flap. Another small patch pocket (130x70 mm), with a flap on one button, is located on the outer upper part of each of the sleeves. Each of these pockets has, hidden under one of the sides, a small mortise wedge for some increase in volume. Under the sleeves, in the armpits, there is a small triangular vent valve, closed with nylon mesh. The edges of the sleeves are tied with a rubber band sewn in at the wrists, and the elbow areas are reinforced with a double layer of fabric. The hood and upper part of the jacket are equipped with a system of special loops to secure additional elements of camouflage. Two loops are located on the right and left hemispheres of the hood; two more-in the chest area (one above each pocket); five loops – in the upper part of the back (as if forming the letter "X") and two - in the upper outer part of the sleeves (one per sleeve). Trousers have a double layer of fabric compacted waist part, slightly tightened, on the right and left, sewn sections of rubber tape. Each of the five belt entablatures with a dial arrangement for 2, 4, 6, 8 and 10 o'clock has a hidden pair of smaller sizes, which allows you to use wide belts up to 60 mm and narrow ones up to 35 mm. In addition, the waist part has a built-in cord that allows you to wear trousers without a belt. In addition, at the top of the waist part, with a dial arrangement at 3 and 9 o'clock, two nylon loops are sewn to attach the suspenders. The flap-covered V-neck of the trousers closes with five buttons. In the front part of the trousers, just under the belt, on both sides there are deep classic cut-in pockets. Below, on both trousers, there are large patch hip pockets (240x210 mm) covered with two-button flaps, with a margin in volume due to three mortise wedges on each. Two more small patch pockets (130x130 mm) with flaps, with a collar, on one button, are located at the back, right and left, below the waist, in the buttock part of the trousers. In the lower groin of the trousers there is a small triangular vent valve closed with nylon mesh. Sections of trousers, compacted with a double layer of fabric and tied with a sewn rubberized tape, are additionally equipped with built-in folding aprons-anther. The latter can be tucked into shoes, with fixing "strips" and additional cord ties. The seat, knee and ankle areas of the trousers are reinforced with a double layer of fabric. The main seams of the KM-L suit are made using the technology of a chain stitch seam. The edges of the belt entablature and the corners of the pocket valves are reinforced with zig-zag fasteners. The manufacturer reserves the right to make changes to the design, materials and configuration of products without prior notice to the consumer. the product is made to order.The production time of 3-5 weeks
Изображения
  • Issue Suit
  • Issue Suit
  • Issue Suit
  • Issue Suit
  • Issue Suit
  • Issue Suit
  • Issue Suit
  • Issue Suit
Customer reviews:
You can add first review.
счетчик посещений